Whirlpool Induction Cooker Error Codes
Error Code F0
Error: An internal error was detected.
Solution: Disconnect power. Wait 5 seconds before reconnecting the power. If the symbol appears again, call for service.
Error Code F2
Error: The surface cooking area is too hot and has been turned off.
Solution: Remove the pans from the surface cooking area. "F2" will disappear when the surface cooking area has cooled. If you turn the surface cooking area back on and "F2" reappears, the cooktop is still too hot. Turn off the surface cooking area and allow it to cool.
Error Code F4
Error: The pot or pan is too close to the control panel.
Solution: Make sure the pot or pan is centered on the surface cooking area and nothing hot is on the touch control panel. Wait 5 minutes for the control panel to clear. If "F4" appears after turning the surface cooking area back on, call for service.
Error Code F8
Error: The surface cooking area has been in operation too long.
Solution: The surface cooking area automatic shutoff was activated. Turn off the surface cooking area.
Error Code C1
Error: The power voltage is too low.
Solution: Turn off the cooktop. Wait 5 seconds, then turn it back on. If this continues, contact a qualified electrician.
Error Code C2/C3
Error: The cooking surface area has overheated.
Solution: The surface cooking area automatic shutoff was activated. Wait 5 minutes for it to cool, and then turn it back on.
Whirlpool Induction Cooker Error Code List
| Error Code | Solution | |
| E0 | Ensure the pot or pan is placed correctly | |
| E1 | The circuit has malfunctioned | |
| E2 | The temperature sensor is an opening circuit or short circuit | |
| E3 | The voltage is higher (140V-160V)for 3 seconds | |
| E4 | The voltage is lower (80V-100V) for 3 seconds. | |
| E5 | The cook-top surface temperature is too high | |
| E6 | Internal Electronic Temperature is higher than normal for 3 seconds | |
| E7 | An internal Electronic Temperature sensor is an opening circuit or short circuit |
Here is a list of Whirlpool induction cooker error codes and their solutions:
| Error Code | Solution |
|---|---|
| F1 | The hob is not turned on. Turn on the hob and try again. |
| F3 | The hob is not connected to the power supply. Make sure that the hob is connected to a power outlet and that the power is turned on. |
| F12 | The hob has detected a fault with the communication system. Turn off the hob and contact Whirlpool customer service for assistance. |
| F22 | The hob has detected a fault with the key sensitivity. Turn off the hob and contact Whirlpool customer service for assistance. |
If you are still having trouble after trying these solutions, you may need to contact a qualified electrician or Whirlpool customer service for assistance.
Here are some additional tips for troubleshooting Whirlpool induction cooker errors:
- If the error code appears immediately after turning on the hob, it may be a problem with the power supply. Try unplugging the hob for a few minutes and then plugging it back in.
- If the error code appears while you are cooking, it may be a problem with the cookware. Make sure that you are using cookware that is compatible with induction cooking.
- If you have tried all of the troubleshooting steps and you are still having problems, you may need to have the hob serviced.
Here are some safety tips for using a Whirlpool induction cooker:
- Do not use the hob if it is damaged.
- Do not use the hob if there is any liquid or food on the surface.
- Do not use the hob if the power cord is damaged.
- Do not use the hob if the hob is not level.
- Do not use the hob if the hob is not properly installed.
- Do not use the hob if the hob is not properly cleaned.
By following these safety tips, you can help to prevent accidents and keep your Whirlpool induction cooker in good working order.
Please note that this is not an exhaustive list of Whirlpool induction cooker error codes and solutions. For more information, please consult your Whirlpool induction cooker user manual.