RAYMOND Forklift Error Codes DTC

RAYMOND Forklift Error Codes DTC

RAYMOND Forklift Truck Error Codes list C14 - Arm Angle Reference Warning C19 - Default Parameter Warning C20 - Thumb Control Warning C23 - Master Control ON / OFF Switch Warning E101 - Power Amplifier Doesn't Correspond with the Type of Truck E104 - Brake Output Error E106 - Digital Output or Field Overcurrent E107 - Contactor Off E108 - Contactor Welded or Missing E110 - Braking System Fault E112 - Arm Angle Sequence Fault E114 - Traction Motor Speed Fault E140 - Checksum Error E141 - Software Problem E142 - Power Amplifier Disable Error E150 - Drive Communication Error E151 - Drive Communication Tx Error E157 - CAN-bus Off Error E159 - Over Run Error E160 - Error In Reversing Circuit E161 - Lower Valve Error E200 - Field Open E201 - M-Error E202 - Power Amplifier Sensor Error E214 - Power Amplifier CAN Time-out

Here is a brief explanation of each code:

• C14: Arm Angle Reference Warning. This means that the arm angle sensor is not detecting the correct position of the mast.
• C19: Default Parameter Warning. This means that the forklift has reverted to its default settings.
• C20: Thumb Control Warning. This means that the thumb control is not working properly.
• C23: Master Control ON / OFF Switch Warning. This means that the master control ON / OFF switch is not working properly.
• E101: Power Amplifier Doesn't Correspond with the Type of Truck. This means that the power amplifier is not compatible with the forklift.
• E104: Brake Output Error. This means that there is an error with the brake output circuit.
• E106: Digital Output or Field Overcurrent. This means that there is too much current flowing through the digital output or field circuit.
• E107: Contactor Off. This means that the contactor is not turning on.
• E108: Contactor Welded or Missing. This means that the contactor is welded shut or missing.
• E110: Braking System Fault. This means that there is a problem with the braking system.
• E112: Arm Angle Sequence Fault. This means that the arm angle sequence is not working properly.
• E114: Traction Motor Speed Fault. This means that there is a problem with the traction motor speed.
• E140: Checksum Error. This means that there is an error in the checksum of the data being transmitted.
• E141: Software Problem. This means that there is a problem with the software of the forklift.
• E142: Power Amplifier Disable Error. This means that the power amplifier has been disabled.
• E150: Drive Communication Error. This means that there is an error in the communication between the drive and the forklift.
• E151: Drive Communication Tx Error. This means that there is an error in the transmission of data between the drive and the forklift.
• E157: CAN-bus Off Error. This means that the CAN-bus is not turned on.
• E159: Over Run Error. This means that the forklift has exceeded its maximum speed.
• E160: Error In Reversing Circuit. This means that there is an error in the reversing circuit.
• E161: Lower Valve Error. This means that there is an error with the lower valve.
• E200: Field Open. This means that the field is open.
• E201: M-Error. This means that there is an error with the M-sensor.
• E202: Power Amplifier Sensor Error. This means that there is an error with a sensor in the power amplifier.
• E214: Power Amplifier CAN Time-out. This means that the power amplifier has not received a message from the CAN-bus in a certain amount of time.

It is important to note that these are just some of the error codes that can occur on RAYMOND forklift trucks. The specific error codes that will appear will vary depending on the model of the forklift. If you are experiencing an error code on your forklift, it is important to consult the owner's manual or contact a qualified technician for assistance.